Knowledge Battery Testing What role does the 2H-to-1T phase transition play in enhancing MoS₂ electrocatalysts for HER? Learn key processing tips to preserve the active phase and boost performance.
Author avatar

Tech Team · Kintek Solution

Updated 3 months ago

What role does the 2H-to-1T phase transition play in enhancing MoS₂ electrocatalysts for HER? Learn key processing tips to preserve the active phase and boost performance.


The 2H-to-1T transition converts MoS₂ from a poorly conducting semiconductor into a metallic electrocatalyst with substantially improved HER kinetics. The metallic 1T phase provides better charge transport and a more favorable electronic structure for hydrogen adsorption and reaction, enabling a kinetically favorable Volmer–Heyrovsky pathway with reported Tafel slopes of approximately 42 mV dec⁻¹. Because 1T-MoS₂ is metastable, however, electrode fabrication and cell assembly must preserve the phase and prevent reversion to less-active 2H-MoS₂.

Core takeaway: Phase conversion is valuable because it improves both electronic conductivity and HER reaction kinetics, but the benefit is only retained when temperature, atmosphere, mechanical force, and slurry-processing conditions are carefully controlled.

Why the 2H-to-1T Transition Improves HER Performance

The limitation of conventional 2H-MoS₂

The conventional 2H phase of MoS₂ is semiconducting. Its limited electrical conductivity can restrict electron transfer from the electrode to catalytically active sites, reducing practical HER efficiency.

This means that even when the material contains chemically active sulfur-related sites, the overall electrode may be limited by charge transport.

The electronic advantage of the 1T phase

The metastable 1T phase is metallic, allowing electrons to move more readily through the catalyst layer. This improved conductivity reduces an important kinetic bottleneck during hydrogen evolution.

The phase transition also changes the MoS₂ d-orbital electronic structure, which influences hydrogen adsorption and the energetics of the elementary HER steps.

The impact on HER kinetics

The 1T phase supports a more favorable Volmer–Heyrovsky reaction pathway, in which electrochemical hydrogen adsorption is followed by electrochemical hydrogen release. This is associated with a low reported Tafel slope of roughly 42 mV dec⁻¹, indicating improved reaction kinetics under the stated conditions.

The phase transition therefore does more than increase conductivity: it changes the electronic environment that governs the catalytic reaction itself.

What the Phase Conversion Involves

Alkali intercalation as the usual route

The 2H-to-1T conversion is commonly induced through alkali-metal intercalation. Intercalated species modify the electronic structure and can drive the MoS₂ layers into the metastable metallic configuration.

The resulting material is often a mixture of phases rather than a perfectly uniform 1T structure, so phase composition and stability must be verified rather than assumed.

Why the converted phase is metastable

The 1T phase is energetically less stable than the conventional 2H phase under many conditions. As a result, it can undergo phase back-conversion during subsequent processing or operation.

This instability is central to practical catalyst preparation: a material that is highly active immediately after conversion may lose performance if fabrication conditions cause partial recovery of the 2H phase.

Processing Considerations for Preserving the Active Phase

Control temperature throughout fabrication

Temperature must be controlled during drying, slurry preparation, electrode assembly, and cell fabrication. Excessive or poorly controlled heating can promote structural relaxation and conversion back toward the less-active 2H phase.

Processing temperatures should therefore be selected to preserve the converted phase rather than treating thermal steps as routine operations.

Maintain a suitable atmosphere

Atmosphere control is also important. Exposure to inappropriate environmental conditions during processing can alter the metastable phase or introduce changes in the catalyst and electrode interface.

Where necessary, processing should be conducted under a controlled atmosphere, with minimized exposure to conditions known to accelerate phase degradation.

Apply mechanical force consistently

Mechanical force matters during pressing and electrode assembly. Excessive or nonuniform pressure can damage the catalyst layer, alter its morphology, or contribute to phase instability.

High-precision laboratory presses are useful because they allow the applied force to be controlled and reproduced between samples.

Control slurry-processing conditions

Slurry preparation affects how the catalyst, binder, conductive additives, and solvent are distributed across the electrode. Mixing, coating, drying, and handling should be standardized to avoid differences in catalyst loading, aggregation, or local mechanical stress.

Repeatable slurry processing is especially important when comparing HER performance, because apparent catalytic improvements can otherwise result from electrode fabrication differences rather than phase composition.

Preserve consistency during cell fabrication

The electrode should not be treated as chemically and structurally unchanged after synthesis. Every post-synthesis step—including pressing, drying, transfer, and cell assembly—can influence the final 1T content and the measured electrochemical response.

Precise control of temperature, atmosphere, and force helps ensure that the catalyst tested in the cell is representative of the synthesized material.

How Phase Stability Affects Electrochemical Measurements

Avoid measuring a changing catalyst as though it were static

If 1T-MoS₂ partially converts back to 2H-MoS₂ during preparation or testing, the measured HER activity may decline or vary between experiments. The resulting data can be difficult to interpret because the catalyst composition is changing during the measurement process.

Phase preservation is therefore part of measurement validity, not merely a manufacturing detail.

Standardize the electrode history

Electrodes should experience the same processing sequence, including slurry handling, drying, pressing, storage, and cell assembly. Differences in processing history can produce differences in phase stability and electrochemical performance.

Using reproducible equipment and defined operating procedures improves comparability across samples and experiments.

Confirm phase retention where possible

The active-phase assignment should be checked after relevant processing steps when practical. Evidence collected only from the as-synthesized powder may not accurately describe the material after electrode fabrication.

This is particularly important for metastable materials, whose structure can change during handling.

Common Pitfalls to Avoid

Assuming all MoS₂ has the same catalytic behavior

The 2H and 1T phases should not be treated as interchangeable. Their electrical properties, electronic structures, and HER kinetics differ substantially.

A reported improvement should therefore be linked to phase composition as well as surface area, loading, and electrode architecture.

Treating alkali intercalation as the end of the process

Successful intercalation does not guarantee that the 1T phase will survive fabrication. Post-synthesis processing can erase part of the benefit through phase back-conversion.

The complete workflow—from conversion through cell assembly—must be designed around phase preservation.

Ignoring fabrication-related variability

Changes in pressing force, drying temperature, atmosphere, or slurry preparation can create apparent performance differences between electrodes. Without process control, electrochemical data may reflect fabrication variability rather than intrinsic catalytic activity.

Overstating the meaning of a low Tafel slope

A Tafel slope near 42 mV dec⁻¹ supports favorable HER kinetics under the relevant measurement conditions, but it should not be used alone to establish overall catalyst superiority. Activity also depends on loading, active surface area, resistance, stability, and measurement quality.

Making the Right Choice for Your Goal

The phase transition should be considered a combined materials-design and process-control strategy, not simply a chemical modification.

  • If your primary focus is maximizing HER kinetics: Favor a well-preserved 1T-rich MoS₂ structure because its metallic conductivity and altered electronic structure can support faster Volmer–Heyrovsky kinetics.
  • If your primary focus is reproducible electrochemical data: Standardize temperature, atmosphere, pressing force, slurry preparation, drying, and cell assembly across every electrode.
  • If your primary focus is long-term catalyst reliability: Treat phase stability as a central design requirement and assess whether processing or operation drives reversion toward 2H-MoS₂.
  • If your primary focus is fair material comparison: Verify phase retention after electrode fabrication rather than relying only on characterization of the starting powder.

Preserving the 1T phase from synthesis through measurement is what converts its theoretical catalytic advantage into reliable HER performance.

Summary Table:

Aspect 2H-MoS₂ 1T-MoS₂
Electronic Conductivity Semiconducting, limited charge transport Metallic, enhanced electron transfer
HER Kinetics Slower, less favorable pathway Faster, Volmer-Heyrovsky with Tafel slope ~42 mV/dec
Stability Thermodynamically stable Metastable, can revert to 2H
Processing Needs Standard Strict control of temperature, atmosphere, and force
Ideal Use Baseline comparison High-performance HER catalysts

Enhance your MoS₂ HER catalyst development with KINTEK's precision equipment.

Achieve reliable 1T-phase retention with our controlled-atmosphere furnaces, precision presses, and slurry processing solutions. From R&D to pilot production, our tools are designed for reproducibility. Contact us today to optimize your workflow and accelerate your breakthroughs.

Contact KINTEK Now


Leave Your Message