Knowledge Battery Testing Why is odd-harmonic, phase-randomized pseudorandom noise used in high-speed EIS? Enhance Your Battery Testing with Faster, Accurate Impedance Measurements
Author avatar

Tech Team · Kintek Solution

Updated 3 months ago

Why is odd-harmonic, phase-randomized pseudorandom noise used in high-speed EIS? Enhance Your Battery Testing with Faster, Accurate Impedance Measurements


Odd-harmonic, phase-randomized pseudorandom noise is used because it produces broad, rapid spectral excitation while reducing distortion, nonlinearity, and excessive signal peaks. The odd-harmonic frequency plan separates key excitation tones from the even-order distortion products generated by the electrochemical cell. Randomizing the phase reduces crest factor, helping keep the cell within its linear operating region, while equal spectral amplitudes provide broadly consistent excitation across the measurement band.

The strategy is a compromise between speed and measurement integrity: excite many frequencies simultaneously, but shape the waveform so that nonlinear distortion and large voltage excursions are less likely to corrupt the impedance estimate.

Why Conventional Sequential Excitation Is Too Slow

EIS normally measures one frequency at a time

Traditional impedance spectroscopy applies a sinusoid at each frequency, measures the current response, and then repeats the process across the frequency range.

This provides excellent frequency discrimination, but the total test time can become long—especially when low-frequency points require several cycles for a stable measurement.

Pseudorandom excitation measures many frequencies at once

A pseudorandom waveform can be constructed by summing many sinusoidal components. The system then uses synchronous detection or a Fourier transform to estimate the voltage-to-current response at all selected frequencies from a single time record.

This enables much faster testing while retaining frequency-resolved impedance information.

How Odd-Harmonic Selection Reduces Distortion Overlap

Nonlinear cells generate harmonic products

An ideal electrochemical interface responds linearly: doubling the excitation amplitude doubles the response without changing its waveform.

Real cells are not perfectly linear. Their voltage-current relationship can generate harmonics and intermodulation products, including second-harmonic components at twice the excitation frequency.

Odd excitation frequencies place second harmonics elsewhere

If the excitation tones occupy odd multiples of a base frequency, their second harmonics occur at even multiples.

For example, an excitation component at (3f_0) produces a second harmonic at (6f_0), which is outside the selected odd-harmonic measurement set. This makes even-order distortion easier to identify and exclude from the primary impedance bins.

Odd harmonics do not eliminate every distortion mechanism

This choice is not a complete solution to nonlinearity. Third-order distortion can occur at odd frequencies and may overlap another selected excitation tone.

Therefore, the odd-harmonic plan reduces a major class of interference—particularly even-order harmonic contamination—but the system must still control amplitude, inspect coherence, and verify linearity.

Why the Phases Are Randomized

Fixed phases can create large peaks

When many sinusoidal components are added with aligned or poorly chosen phases, their peaks can occur at the same instant.

The result is a high-crest-factor waveform with a much larger peak-to-peak voltage than its individual components suggest. That can overdrive the potentiostat, perturb the electrode interface, or move the cell outside the small-signal region required for conventional EIS.

Random phases spread the energy in time

Assigning different pseudorandom phase angles makes simultaneous peak alignment less likely.

The waveform still contains all intended frequency components, but its instantaneous amplitude is distributed more evenly. This generally lowers the crest factor and allows useful broadband excitation at a safer overall amplitude.

Phase randomization supports linear operation

Keeping the electrochemical system in its linear—or approximately linear—region is essential because impedance is defined as a small-signal response.

If the excitation is too large, the measured response may describe amplitude-dependent nonlinear behavior rather than the local impedance the test is intended to characterize.

Why a White Spectrum Is Useful

Equal component amplitudes simplify spectral coverage

A white or approximately white excitation assigns similar amplitude to the selected frequency components.

This gives each measurement bin comparable input energy, making the test less likely to neglect particular frequencies simply because they received much less excitation.

It supports more uniform signal-to-noise performance

The impedance estimate at a frequency depends on the quality of both the voltage and current measurements at that frequency.

Equal excitation weighting helps provide a more consistent signal-to-noise ratio across the evaluated band, although the final SNR still depends on instrument noise, cell impedance, bandwidth, and the current-measurement range.

It makes the waveform easier to interpret

A deliberately flat spectral weighting means that differences in the measured response are more directly attributable to the electrochemical system rather than to strong variation in excitation amplitude.

This is particularly useful when comparing impedance behavior across a wide frequency range.

Why This Matters in High-Speed Battery Testing

The waveform combines speed with small-signal control

High-speed testing requires many frequency points to be acquired in a short time.

Odd-harmonic, phase-randomized excitation addresses the main practical constraints simultaneously: it provides parallel frequency coverage, reduces peak excursions, and separates selected tones from important distortion products.

It reduces the risk of damaging or polarizing the interface

A controlled multisine-like waveform can achieve the required measurement bandwidth without applying unnecessarily large transient voltages.

That supports non-destructive testing and reduces the chance that the test itself significantly changes the electrochemical state being measured.

It improves confidence in automated measurements

Battery analytical systems often need repeatable measurements across many cells and operating conditions.

A carefully designed excitation signal makes the measurement more predictable, but it does not replace validation. Automated systems should still monitor amplitude, coherence, residual error, and signs of nonlinearity.

Understanding the Trade-offs

Odd harmonics reduce usable frequency density

Restricting excitation to odd harmonics leaves gaps between available tones compared with a fully populated frequency grid.

The reduced density is accepted because it creates cleaner separation from even-order distortion and can simplify frequency-bin analysis.

Random phases reduce peaks statistically, not absolutely

Phase randomization lowers the probability of severe constructive interference; it does not guarantee a constant-amplitude waveform or eliminate all large peaks.

Practical systems may still need amplitude margins, crest-factor checks, clipping detection, and carefully selected phase sets.

Flat excitation does not guarantee flat measurement quality

Equal voltage amplitudes do not produce equal current amplitudes when the cell impedance varies strongly with frequency.

At some frequencies, the current response may be small relative to instrument noise; at others, it may approach the safe operating limit. Excitation amplitude and weighting may therefore need to be adapted to the cell and instrument.

Faster acquisition can expose nonstationarity

A rapid broadband test assumes that the cell is sufficiently stable during the measurement record.

If state of charge, temperature, contact conditions, or electrode behavior changes significantly during acquisition, the resulting spectrum may not represent a single stationary impedance state.

Making the Right Choice for Your Goal

The excitation design should be treated as part of the measurement-control strategy, not merely as a waveform-generation detail.

  • If your primary focus is measurement speed: Use simultaneous mult frequency excitation so many impedance points can be estimated from one record, while ensuring the acquisition window is long enough for the lowest-frequency components.
  • If your primary focus is linearity: Use phase randomization and conservative amplitude limits to reduce crest factor and keep the electrochemical interface in its small-signal region.
  • If your primary focus is distortion rejection: Use odd-harmonic placement to move second-order distortion into unexcited even-harmonic bins, while checking for third-order and intermodulation products.
  • If your primary focus is uniform spectral accuracy: Use approximately equal component amplitudes, then verify actual SNR because cell impedance and instrument noise can still vary substantially with frequency.
  • If your primary focus is reliable production testing: Combine the waveform strategy with coherence, clipping, residual-error, and repeatability checks rather than assuming the excitation alone guarantees valid EIS data.

Odd-harmonic, phase-randomized pseudorandom noise enables fast EIS without giving up control over distortion, peak amplitude, or spectral coverage.

Summary Table:

Strategy Purpose Key Benefit
Odd-harmonic selection Separate excitation tones from even-order distortion Reduces nonlinearity interference
Phase randomization Spread waveform peaks Lowers crest factor, keeps cell linear
White spectrum Equal amplitude across frequencies Uniform SNR and spectral coverage
Multisine excitation Simultaneous frequency measurement Rapid EIS acquisition

Ready to accelerate your battery R&D? KINTEK provides advanced EIS systems and comprehensive laboratory equipment for battery research and materials science. Our solutions are designed to deliver fast, accurate, and reliable impedance measurements. Contact us today to optimize your testing workflow and bring your innovations to market faster. Get in touch with our experts.


Leave Your Message